Download the free trial version below to get started. Double-click the downloaded file to install the software. I'm new to cisco kit, I've been on the CCNA course years ago (2009-ish) but shouldn't have been sent at that time as I really was just 1st line and had no kit in the office to practice with after so it's all travelled away from my brain! My new boss has purchased a 5505 for the office and I'm attempting to.

To connect cables to the ports perform the following steps: Step 1Place the chassis on a flat, stable surface. Step 2Before connecting a computer or terminal to the ports, check to determine the baud rate of the serial port. The baud rate must match the default baud rate (9600 baud) of the Console port of the adaptive security appliance. Set up the terminal as follows: 9600 baud (default), 8 data bits, no parity, 1 stop bits, and Flow Control (FC) = Hardware. Step 3Connect the cables to the ports. A.Ethernet ports Step 1Connect Port 0, the outside Ethernet port, to the public network, that is, the Internet.

Free Bible Timeline Pdf. Cisco ASA 5505 Series. Adaptive Security Appliance. 1 Power 48VDC. Console port. USB 2.0 interface. 3 Network interface LEDs. Reset button. 4 Network interfaces1. Ports 6 and 7 are 15-Watt output PoE ports, used for devices, such as IP phones, which can be powered by the network interface. NET 3.5 SP1 or higher - Cisco blue serial to RJ45 cable. Network Requirements: Obtain a static IP address for the ASA 5505 for use on the house network. Determine the IP address scheme for the Ignite network - by default it can be 192.168.1.X or 10.11.1.X, this can be determined.

Step 2Connect your network devices with an Ethernet cable to one of the inside ports (numbered 1 through 7). If you are connecting any PoE devices, connect them to one of the switch ports that support PoE (ports numbered 6 and 7). Step 3Check the LINK LED to verify that the network devices have basic connectivity to the Cisco ASA 5505 on one of the inside ports (numbered 0 through 7). When connectivity is established, the LINK LED on the front panel of the Cisco ASA 5505 lights up solid green.

Figure 3-1Connecting Cables to Network Interfaces. B.Console port You can access the command line for administration using the console port on theCisco ASA 5505. To connect to the console port and run a serial terminal emulator on a PC or workstation, perform the following steps: Step 1Plug one end of the PC terminal adapter into a standard 9-pin PC serial port on your PC. Step 2Plug one end of the blue console cable into the PC terminal adapter. Step 3Plug the other end of the blue console cable into the Console port. Step 4Configure the PC terminal emulation software or terminal for 9600 baud, 8 data bits, no parity, and 1 stop bit.

WarningTo prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: This unit should be mounted at the bottom of the rack if it is the only unit in the rack. When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006. The following information can help plan equipment rack installation: • Allow clearance around the rack for maintenance. • If the rack contains stabilizing devices, install the stabilizers prior to mounting or servicing the unit in the rack. 1143 Tale Of The Comet Pdf Printer.

• When mounting a device in an enclosed rack, ensure adequate ventilation. Do not overcrowd an enclosed rack. Make sure that the rack is not congested, because each unit generates heat. • When mounting a device in an open rack, make sure that the rack frame does not block the intake or exhaust ports.

• If the rack contains only one unit, mount the unit at the bottom of the rack. • If the rack is partially filled, load the rack from the bottom to the top, with the heaviest component at the bottom of the rack. This section contains the following topics: • •. 2 Plastic anchors Step 3Drill a hole on the wall at each mark you made for the location for the plastic anchors. Step 4Press the four plastic anchors into the holes.